SPA122 Setup Guide

Here you can post your own working configurations of hardware or software to share with other users who may be using the same device!
Fongo recommends Fongo Home Phone for a fully supported Home Phone system for only $4.95/mo
Forum rules
DISCLAIMER
This forum is for those users who have already purchased a configuration file with the SIP settings needed to configure any SIP compatible device.

1. Please use this forum only as a means to share your configuration advice and guides for ATA devices and SIP clients that you are using with our service.
2. For any questions relating to device configuration, please use the other forum sections or post your question directly in the device topic that your question is meant for.
3. Please title your topics with only the name and model of your device so users can easily find the information they need.
4. Preferable format for posting here is compressing your screenshots of your successfully configured device into a .zip file, and post a brief description of the configuration.

Please stay on topic

SPA122 Setup Guide

Postby Jake » 08/11/2014

Credits to Val, thank you for your help.

The attached PDF will help you set up your SPA122 device from scratch. It is a known working configuration so if you are having troubles with your SPA122 reset back to defaults and follow this guide.

Edit by LiptonBrisk: 1.Navigate to Voice-->SIP tab-->SIP Timer Values (sec)-->Reg Retry Intvl should be 120 seconds
https://support.freephoneline.ca/hc/en- ... redentials

2. (Do what Mango wrote below.)
In your SPA122 ATA, navigate to Voice-->SIP tab-->NAT Support Parameters, and make sure that the following settings are enabled:

a)Handle VIA received-->yes
b)Handle VIA rport-->yes
c)Substitute VIA Addr-->yes

3. In your SPA122 ATA, navigate to Voice-->Line 1 (or whatever Line you're using for FPL)-->SIP settings, and change SIP Port to a random number between 30000 and 60000. Do this for security reasons (to help avoid SIP Scanners/hackers). Also, this step may help to temporarily address a corrupted NAT association that's developed between a router and ATA (if you're having registration issues, try selecting a new random port number in this range, and then reboot the ATA. If that works, you were dealing with a corrupted/stale NAT association in your router).

4. In your ATA, navigate to Voice-->Line (whichever you use for FPL)-->Supplementary Service Subscription-->Block CID Serv:
a) change to no
b) Click "submit"
Do this to avoid 15 minute call drops.
Attachments
Cisco SPA122 ATA Config FreePhoneLine.pdf
(1.14 MiB) Downloaded 4335 times
User avatar
Jake
Technical Support
 
Posts: 2823
Joined: 10/18/2009

Re: SPA122 Setup Guide

Postby Mango » 01/16/2015

To prevent one-way or no audio with the new FPL switches, set the following from within Voice >> SIP:

Handle VIA received: yes
Handle VIA rport: yes
Substitute VIA Addr: yes
Mango
Tried and True
 
Posts: 411
Joined: 08/14/2014
SIP Device Name: OBi110
Firmware Version: 1.3.0 (Build: 2824)
ISP Name: Telus
Computer OS: Windows 7
Router: Toastman Tomato

Re: SPA122 Setup Guide

Postby aha » 04/02/2016

Hi,

This is what finally helped me.

Thanks a lot. I'll post my whole story later but after trouble shooting for days and even convincing rogers to disable SIP ALG on my router, this is what actually solved my one way audio problem where the other person could hear me but I couldn't hear them. Also I wasn't able to connect to certain phone numbers after I dialed. This has also been resolved.
aha
Just Passing Thru
 
Posts: 3
Joined: 04/02/2016
SIP Device Name: Cisco SPA112
Firmware Version: 1.3.5
ISP Name: Rogers
Computer OS: Windows 10
Router: Hitron CGN3ACR

Re: SPA122 Setup Guide

Postby saunders000 » 10/29/2017

Hello,

I have recently switched from BELL DSL to Tecksavvy CABLE and can't get my CISCO ATA to work. I'm wondering whether my Linksys WRT1900ACS router isn't letting traffic through? I've configured the ATA122 using the parameters shared here and am at a loss. Not sure who to ask for help or where to go. Any ideas would be welcomed!! Thanks.
saunders000
One Hit Wonder
 
Posts: 1
Joined: 10/29/2017
SIP Device Name: SPA122
Firmware Version: 1.4.1SR1
ISP Name: Tecksavvy CABLE
Computer OS: Windows 10
Router: Linksys WRT1900ACS

Re: SPA122 Setup Guide

Postby Liptonbrisk » 10/29/2017

saunders000 wrote:Hello,
and can't get my CISCO ATA to work. .


Can you be a little more specific please? What isn't working?
Registration?

1) What does the registration status in the ATA indicate?

Linksys WRT1900ACS


a) Ensure whatever modem/router combo you're using with Teksavvy is in bridge mode.

b) And try disabling SIP ALG
Click https://www.phonepower.com/mediawiki/im ... 00AC09.png

c) Then reboot modem-->router (wait for it to be fully up and transmitting data)-->ATA in that order.
That's always the proper device reboot order.

2) Are you getting 1-way audio issues? Visit viewtopic.php?f=8&t=20532
Please do not send me emails; I do not work for nor represent Freephoneline or Fongo. Post questions on the forums so that others may learn from responses or assist you. Thank you. If you have an issue with your account or have a billing issue, submit a ticket here: https://support.fongo.com/hc/en-us/requests/new. Visit http://status.fongo.com/ to check FPL/Fongo service status. Freephoneline setup guides can be found at viewforum.php?f=15.
User avatar
Liptonbrisk
Technical Support
 
Posts: 2764
Joined: 04/26/2010
SIP Device Name: Obihai 202/2182, Groundwire
Firmware Version: various
ISP Name: FTTH
Computer OS: Windows 64 bit
Router: Asuswrt-Merlin & others


Return to Device Configuration Sharing

Who is online

Users browsing this forum: No registered users and 26 guests