PolyCom Phone Config.

Here you can post your own working configurations of hardware or software to share with other users who may be using the same device!
Fongo recommends Fongo Home Phone for a fully supported Home Phone system for only $4.95/mo
Forum rules
DISCLAIMER
This forum is for those users who have already purchased a configuration file with the SIP settings needed to configure any SIP compatible device.

1. Please use this forum only as a means to share your configuration advice and guides for ATA devices and SIP clients that you are using with our service.
2. For any questions relating to device configuration, please use the other forum sections or post your question directly in the device topic that your question is meant for.
3. Please title your topics with only the name and model of your device so users can easily find the information they need.
4. Preferable format for posting here is compressing your screenshots of your successfully configured device into a .zip file, and post a brief description of the configuration.

Please stay on topic

PolyCom Phone Config.

Postby bbea4 » 12/23/2018

Hello fellow freephone users.
I have search high and low to find the conf setting for using Poycom IP Phones.
I have set the SIP settings and can connect to the voip.freephoneline.ca servers. (following another post ), I DO get a dial tone, but I can not get past the "password in incorrect" message.

Any help would be appreciated.
bbea4
One Hit Wonder
 
Posts: 1
Joined: 12/23/2018

Re: PolyCom Phone Config.

Postby Liptonbrisk » 12/23/2018

While I won't be able to help you with your specific IP phone because I've never used it and can't find any emulators, after purchasing a Freephoneline VoIP unlock key, you can find your SIP Password after logging in at https://www.freephoneline.ca/showSipSettings. Double check to ensure you've entered in your SIP password correctly without any additional spaces before or after it. The error message you're hearing is likely generated by FPL because the SIP password and/or username you've entered isn't correct. If you've ported in a phone number into FPL, your original SIP credentials will have changed (in particular, check your SIP Username).

SIP configuration settings (please make note of the registration and failed registration retry interval timers of 3600 seconds and 120 seconds, respectively) can be found at https://support.freephoneline.ca/hc/en- ... redentials.



--------------------------------------------------------------------------------------
Other important information to take note of is listed below.


A. If your IP Phone makes more than 5 registration attempts in 5 minutes (this is why the registration interval is important),
you may end up being temporarily IP banned by the specific FPL server the ATA was sending
registration requests to (each time you reboot the IP Phone, it's attempting to register with FPL). If you're temporarily IP banned, you could then try switching Proxy to a different FPL server than the one you were previously using (voip.freephoneline.ca, voip2.freephoneline.ca, or voip4.freephoneline.ca:6060), unless you need to use voip4.freephoneline.ca:6060 because you have SIP ALG forced on in your router. The purpose of
voip4.freephoneline.ca:6060 is to circumvent SIP ALG features in routers.


https://community.freepbx.org/t/trunk-s ... ca/22479/8
"As May 2013, our servers will rate limit REGISTER requests to a maximum of 10 requests per 5 minutes. Each authentication round usually consumes 2 requests (digest auth), so it is a fair number given our guidelines. Also, it does not affect INVITES (which are also authenticated)…

This rate limit is applied per IP address as our service is tailored to residential Canadian users (ADSL/Cable)."

B. If the IP Phone loses registration for any reason, incoming calls won't work on it. Note that only one registration per FPL account is allowed at any time. When there are multiple devices/softphones using the same account, only the most recent registration is valid. The previous device will lose registration. This is especially important to consider if someone else is using your SIP credentials (username and password) that are found after logging in at https://www.freephoneline.ca/showSipSettings (or if you're trying to register your FPL account with a smartphone SIP app or with another device). Registration is required for incoming calls. It is not required for outgoing calls. If you simply want to make outgoing calls using your FPL number, configure, but don't register the account, on the SIP app being used. This is also important to consider if you're using Freephoneline's desktop application (don't have it running while using your ATA with the same FPL account). Additionally, keep in mind that if someone else is also attempting to register the same SIP credentials on another device where you live, too many registration attempts can result in a temporary IP ban. Always check registration status in the IP Phone and also your SIP status after logging in at https://www.freephoneline.ca/showSipSettings. If you see a device listed under SIP User Agent that you don't recognize, you've either been hacked or someone else is using your Freephoneline SIP username and SIP Password.


Typically, for VoIP SIP services, especially for freephoneline, you want

1) a router that does not have a full cone NAT,

Visit https://www.think-like-a-computer.com/2 ... es-of-nat/.
Mango from the Obitalk.com forums writes,
“Use a restricted cone NAT router, and do not use port forwarding or DMZ. Restricted cone NAT will only permit
inbound traffic from the service provider you're registered to. If you have a full cone NAT router, it will allow traffic
from any source. This is probably not what you intend.
If you have a Windows computer, you can test your router using the utility here:
http://www.dslreports.com/forum/remark,22292023. To run it, use stun stun.ekiga.net from a command prompt.”
Essentially, you download the stun-test.zip file; extract the stun.exe file from within the zip file to an easily
accessible location; use an elevated command prompt (visit
http://www.thewindowsclub.com/how-to-ru ... inistrator); change directory (cd) to the
directory or location where you extracted stun.exe (visit
http://www.digitalcitizen.life/command- ... c-commands); and type “stun stun.ekiga.net” without
the quotation marks followed by the enter/return button on your keyboard.
Asus routers, at the time of this writing, produce port restricted cone NAT routers, for example and are fine,
provided you’re using one with Asuswrt-Merlin, third party firmware installed.

2) a router that lets you disable SIP ALG if it's buggy,

To understand why SIP ALG often causes horrible problems, please visit
http://www.voip-info.org/wiki/view/Routers+SIP+ALG (scroll down to the section on SIP ALG problems).

If you're dealing with a modem/router combo issued by an ISP or a router with SIP ALG forced on, you may have
to use voip4.freephoneline.ca:6060 for the Proxy Server. The purpose of voip4.freephoneline.ca:6060 is to circumvent
faulty SIP ALG features in routers.
Please do not send me emails; I do not work for nor represent Freephoneline or Fongo. Post questions on the forums so that others may learn from responses or assist you. Thank you. If you have an issue with your account or have a billing issue, submit a ticket here: https://support.fongo.com/hc/en-us/requests/new. Visit http://status.fongo.com/ to check FPL/Fongo service status. Freephoneline setup guides can be found at viewforum.php?f=15.
User avatar
Liptonbrisk
Technical Support
 
Posts: 914
Joined: 04/26/2010
SIP Device Name: OBi202
Firmware Version: 3.2.2 (Build:5921EX)
ISP Name: Cable
Computer OS: Windows 10 x64 Pro
Router: Asuswrt-Merlin

Re: PolyCom Phone Config.

Postby Liptonbrisk » 12/23/2018

*continuing*



3) a router that allows you to set QoS or assign highest priority to your ATA or IP Phone over all other devices on your LAN (local area network),

For a very general description of what QoS can do for you, visit https://www.voipmechanic.com/qos-for-voip.htm.
The basic idea is if you're torrenting or have a bunch of other computers, smartphones, tablets, etc. downloading and uploading (hogging all your available bandwidth), you don't want
your ATA not to have access to enough bandwidth to make or receive calls properly. So QoS or a Bandwidth Monitor feature (which is just another form of QoS) is a really good idea for VoIP users.

I often get an occasional relative complaining to me, "Hey my calls sound choppy." And then when I go visit, some kids are playing MMOs on a computer, while another person is downloading a huge file,
and another person is backing up files to a cloud service all at the same time someone else is trying to talk on the phone. All those devices, without QoS enabled, are fighting over available bandwidth along with the ATA.


and 4) A router that lets you adjust both Unreplied and Assured UDP timeouts.

Thanks to Mango, many of us now understand that in order for ATAs to remain registered and working properly with a VoIP SIP provider like Freephoneline, in particular after power failures, the following conditions must be met:

UDP Unreplied Timeout (in your router) < NAT Keep-alive Interval (in your ATA; for Obihai ATAs this is X_KeepAliveExpires) < UDP Assured Timeout (in your router) < SIP Registration Failure Retry Wait Time (or RegisterRetryInterval in Obihai ATAs)

“<“ means less than.

When a modem leases a new IP address, a problem can arise where prior associations using the old IP address are maintained in the router. When the ATA attempts to communicate using the old IP address, the response is unreplied, and then if the UDP Unreplied timeout is greater than the Keep Alive Interval (and UDP Unreplied timeout is often set to 30 by default in consumer routers) a problem arises where the corrupted connection persists. If UDP Unreplied timeout is, for example, 10, and the NAT Keep Alive Interval is 20, then the corrupted connection will timeout or close. A new connection will be created, and everything will work fine.

Another problem can occur when the Keep-Alive interval is greater than UDP Assured Timeout (often 180 by default in consumer routers): the NAT hole will close due to the ATA not communicating frequently enough with the SIP server. In turn, incoming calls may, intermittently, not reach the ATA. Again, X_Keepalives expires is supposed to be 20 with FPL.

(the above settings are making reference to those in Obihai ATAs/Obihai IP Phones)

Getting access to both UDP Unreplied Timeout and UDP Assured Timeout settings in consumer routers may be difficult, if not impossible. Asuswrt-Merlin (I would avoid any model below/less powerful than an RT-AC68U), third party firmware for Asus routers, does offer easy access to these two settings, which are found under General–>Tools-->Other settings. My understanding is that third party Tomato firmware has these two settings as well. So if your router supports Tomato firmware, that may be another option. Note that I will not be held accountable any damage resulting from failed firmware updates. Apparently, Mikrotik routers also allow users to change both Assured and Unreplied UDP timeout settings as well: https://forums.redflagdeals.com/recomme ... 2115672/2/

The keep alive interval for FPL is 20. The SIP Registration Failure Retry Wait Time is 120. I use 10 for UDP Unreplied Timeout and 117 for UDP Assured Timeout.



ISPs do not issue customers routers that can do all four things I just listed. Typically it's far better to have your own router with strong QoS functions and a restricted cone NAT firewall,
disable whatever SIP ALG feature is enabled in the router, and stick whatever modem/router combo your ISP gives you into bridge mode. For Bell Hubs, visit http://forums.redflagdeals.com/please-s ... r-1993629/. For Rogers, visit https://www.rogers.com/customer/support ... ridgemodem.
Please do not send me emails; I do not work for nor represent Freephoneline or Fongo. Post questions on the forums so that others may learn from responses or assist you. Thank you. If you have an issue with your account or have a billing issue, submit a ticket here: https://support.fongo.com/hc/en-us/requests/new. Visit http://status.fongo.com/ to check FPL/Fongo service status. Freephoneline setup guides can be found at viewforum.php?f=15.
User avatar
Liptonbrisk
Technical Support
 
Posts: 914
Joined: 04/26/2010
SIP Device Name: OBi202
Firmware Version: 3.2.2 (Build:5921EX)
ISP Name: Cable
Computer OS: Windows 10 x64 Pro
Router: Asuswrt-Merlin


Return to Device Configuration Sharing

Who is online

Users browsing this forum: No registered users and 1 guest