Fongo Community Forums

its 192.168.1.100 when it is connected directly to the router. its 192.168.13.100 when it is connect through my PC. I believe I have the IP configurations set up correctly. It seems to be getting some kind of communication. Why else would I get a dial tone? I am using static IP addresses. I have my...

its 192.168.1.100 when it is connected directly to the router. its 192.168.13.100 when it is connect through my PC. I believe I have the IP configurations set up correctly. It seems to be getting some kind of communication. Why else would I get a dial tone? I am using static IP addresses. I have my...

its 192.168.1.100 when it is connected directly to the router. its 192.168.13.100 when it is connect through my PC. I believe I have the IP configurations set up correctly. It seems to be getting some kind of communication. Why else would I get a dial tone? I am using static IP addresses. I have my ...

I have reconfigured as you instructed. I am getting the same result. I get a dial tone and I appear to be registered, but I have no services. The following is the ATA, an HT286, Status Report: IP Address: 192.168.1.100 Product Model: HT287 Rev4.1 Software Version: Program-- 1.1.0.42 Bootloader-- 1....

I have reconfigured as you instructed. I am getting the same result. I get a dial tone and I appear to be registered, but I have no services. The following is the ATA, an HT286, Status Report: IP Address: 192.168.1.100 Product Model: HT287 Rev4.1 Software Version: Program-- 1.1.0.42 Bootloader-- 1.1...

I have a TP-Link TL-WR941ND. My ATA is actually attatched to my ethernet card and I am getting a wireless connection to the router for the internet. Every was working with this configuration. I have tried forwarding the ports, but I haven't needed to do so in the past. I have also tried using a STU...

This is the Status Report of the ATA (Handy Tone 236) IP Address: 192.168.13.100 Product Model: HT287 Rev4.1 Software Version: Program-- 1.1.0.42 Bootloader-- 1.1.0.1 HTML-- 1.1.0.42 VOC-- 1.0.0.13 System Up Time: 0 day(s) 17 hour(s) 8 minute(s) Registered: Yes PPPoE Link Up: disabled NAT: detected ...

I have a TP-Link TL-WR941ND. My ATA is actually attatched to my ethernet card and I am getting a wireless connection to the router for the internet. Every was working with this configuration. I have tried forwarding the ports, but I haven't needed to do so in the past. I have also tried using a STUN...

I am getting a dial tone, but I cannot call out or in. I am in Toronto.

I have a HT-286 plugging into my on-board ethernet port and wireless connection to the internet. I have had no problems with the connection in the past. Recently I installed Expat Shield VPN and noticed that my ATA got disconnected every time I connected the VPN. It would come back once I disconnect...

Thanks, that got rid of the error message. Now if I can just get some stability out of my internet access, ...

Yes, I must remember to chose my sound card from the control panel before loading the soft phone as well, and then switch it back after the soft phone loads for my other audio needs.

If there are any other comments or ideas, I would love to hear them.

I have two network cards running on my computer. One is a wireless adapter for internet access and the other goes to another router for my other network devices. When I start up the soft phone, a hosts file dialog box appears and I must choose which adapter is connected to the internet. Is there a c...

When I checked my ATA, a Handy Tone 286, I get the response, "E 105 E". The phone is working fine, but I am curious what this code means and it is not listed in the manual. Does anybody know?