OBi100 Setup Guide

[Jake]

Credits to cyberic68, thank you for your help.

The attached PDF will help you set up your OBi100 device from scratch. It is a known working configuration so if you are having troubles with your OBi100 reset back to defaults and follow this guide.

Edit by LiptonBrisk: Navigate to Service Providers-->ITSP Profile (FPL)-->SIP
RegisterRetryInterval should be 120 seconds.
https://support.freephoneline.ca/hc/en- ... /212430746
And then do what Mango wrote below.

[Mango]

To prevent calls arriving with caller ID such as 100 or 1001, if the calls do not appear in your call logs on the Freephoneline website, use the following procedure:

1) If you use your router to forward ports to your OBi ATA, remove your port forwarding unless things won't work any other way. If your router has an option like "strict UDP session control", enable it, and/or configure its firewall to be as secure as possible. You are receiving these calls because your router's firewall is insecure.

2) Navigate to Voice Services >> SPx Service. Set X_UserAgentPort to a random number between 20000 and 65535. This will make it more difficult for the scanners to find you. If you must forward ports, you will need to update your port forward.

3) Also from within Voice Services >> SPx Service, set X_InboundCallRoute to {>1xxxxxxxxxx:ph}
If the scanners do find you, this will cause your OBi to reject the call. (Note: replace 1xxxxxxxxxx with your FPL number.)

[WilliamY]

The digit map was wrong in the PDF, instead of 011xxxxxxxxxxxx. it should be 011xx. or you can't make international calls to some countries that take 011 + 10 digit phone#.

[bogolisk]

Code28: *95, Blind Transfer, coll($Bbxrn)

My obi keeps complaining (in syslog): Unknown Variable $Bbxrn

[Equinox]

If I follow the instruction, the call is forwarded to my voicemail. But if I roll back to the default setting, the call is in without problem.
I am using Obi200.

3) Also from within Voice Services >> SPx Service, set X_InboundCallRoute to {>1xxxxxxxxxx:ph}
If the scanners do find you, this will cause your OBi to reject the call. (Note: replace 1xxxxxxxxxx with your FPL number.)

[mh1983]

If I follow the instruction, the call is forwarded to my voicemail. But if I roll back to the default setting, the call is in without problem.
I am using Obi200.

3) Also from within Voice Services >> SPx Service, set X_InboundCallRoute to {>1xxxxxxxxxx:ph}
If the scanners do find you, this will cause your OBi to reject the call. (Note: replace 1xxxxxxxxxx with your FPL number.)

Am not familiar with the Obi ATAs, but the guide/directions in this thread is for the 100, not 200.

[Mango]

The syntax is the same for all models.

[Equinox]

The syntax is the same for all models.

Exactly. Obi200 settting is almost identical as 100 except System Management->Network Settings becomes "WAN Settings". See attached image.
In addition, I am trying to change the admin password. But after reboot, the device still takes the default one. Not sure if it is a bug or not.

[mh1983]

Good to know -- my bad!

[Liptonbrisk]

In addition, I am trying to change the admin password. But after reboot, the device still takes the default one. Not sure if it is a bug or not.

OBi200/202 setup guide can be found at http://forum.fongo.com/viewtopic.php?f=15&t=18805

You'll want to look at page 12 of the .pdf file.

[siyano]

I have been sent here but I don't think its the right troubleshooting for me, this help for network and (real?) phone management
but im using the program and direct connection

[Liptonbrisk]

I have been sent here but I don't think its the right troubleshooting for me

It's not. This thread has nothing to do with the FPL desktop app, but you never explained what you were using when you posted either (always post router brand and model in addition to whether you're using the FPL desktop app).