SIP Sorcery (www.sipsorcery.com) on Linksys PAP2T

[FONGO_steve]

Please Note:
Guides for third-party hardware are provided on an as-is purpose for reference only. We will not provide any direct support for third party hardware, nor can we be held responsible for any mistakes in these guides.

For those looking to channel multiple SIP accounts to one device, check out http://www.sipsorcery.com.

Linksys PAP2T ATA configuration is as follows:

Inbound Proxy: sip.sipsorcery.com
Use Outbound Proxy: Yes
Outbound Proxy: sip.sipsorcery.com

User ID: your SIP Sorcery username
Password: Your SIP Sorcery password

Preferred Codec: G729a
Use pref codec only: No

Dial Plan: ([x*][x*].)
*Note that you must configure a dial-plan directly on the SIP Sorcery website or your calling will not work
*Devices using the numbers here must be unregistered on all devices except the one you are using with http://www.sipsorcery.com.

[axu]

Hi mindabsence,

Thanks for provide the sipsorcery information, and I was surf some time, and found the dial plan for sipsorcery on ruby is so powerful, same as so complex, do you have any document on that information ? like how to confirm the FPL on the sipsorcery sip provider( actually this step I already done, but don't know if it is right, it said registered in the down part of the browser ( SIP Provider Registrations ), however, I have no idea on the dial plan for ruby. it's so complex, and can you give me some clue on that ? like dial in / out plan for the single / multi channel of freephoneline config file account ?
I was found some on their forum ( http://www.mysipswitch.com/forum/index.php ) and somebody said the dial plan can be use, maybe I don't understand the syntax, and it's can't work on my FPL account.

[FONGO_steve]

Hi mindabsence,

Thanks for provide the sipsorcery information, and I was surf some time, and found the dial plan for sipsorcery on ruby is so powerful, same as so complex, do you have any document on that information ? like how to confirm the FPL on the sipsorcery sip provider( actually this step I already done, but don't know if it is right, it said registered in the down part of the browser ( SIP Provider Registrations ), however, I have no idea on the dial plan for ruby. it's so complex, and can you give me some clue on that ? like dial in / out plan for the single / multi channel of freephoneline config file account ?
I was found some on their forum ( http://www.mysipswitch.com/forum/index.php ) and somebody said the dial plan can be use, maybe I don't understand the syntax, and it's can't work on my FPL account.

Hey axu,
Check out the ruby dial plan wizard on mysipswitch.com. I used it to create my ruby plan and it's very straightforward - much like building a sentence of call routing.

Setting up your FPL account in sipsorcery is fairly simple:
username and password are your SIP username and password we give you in the config file.
Server is the voip.freephoneline.ca
Provider name you can fill in yourself
Check the register box
and let it auto-fill the other fields - only thing in advanced you need to change is register expires to 3600.

Let me know if you're having any troubles with that, I can try and clarify and guide you more if need be

[mohnashaat]

is SIPSorcery down ? any news about it? is there any other similar sevices?

[Jake]

Yes it look slike it is down at the moment. ccording to their blog http://sipsorcery.wordpress.com/ they did an update a few days ago. Maybe this has something to do with it. Reading the comments it looks like other people have the same problem. Let's hope it is fixed soon.

I also found this in a forum http://www.mysipswitch.com/forum/viewto ... ght=#11440

[Jake]

They have come back online now. There is a post about it on their blog.

[FONGO_kris]

Sounds good!

[kola]

hi steve,

i was trying all the instruction to configure my account with sipsorcery. Outgoing are no problem, but i am unable to get the incoming. It says person u are trying to reach is offline.

I tried with the ruby wizard but still doesn't work.

Please provide your espert advise. It would be great, if you can send me ur dial plan settings.....

Thanks,

Kola

[kola]

hi steve,

I had a small question regarding the dial plan. Please see the file & i shall wait for your reply.

Thanks

[FONGO_kris]

As far as I can tell in the rough config I did using SIPSorcery, you would add 1+ your ten digit phone number.

[kola]

Hey Kris/Steve,

I am so excited, i got it running...........thank you so much for your support...

Thanks once again....

Kola//

[FONGO_steve]

I didn't enter my number in that spot.. did you? Mine works without anything entered in there.

[kola]

yes i did but since it has started working i will remove the number see, if i still get calls.

[Ice]

I actually have the SPA3102 and I'm having a problem where can receive calls but I can't dial out - I get a fast busy signal. I'm assuming the profile "link" between Sorcery and FPL is set up correctly, but at this point I'm willing to admit the problem could be anywhere. I've methodically tried various settings from this thread and others, and also trial and error but nothing seems to work. Anybody have any ideas?

Right now my dialing profile goes:
sys.Dial("FPL") ...where FPL is the name of the SIP Provider profile...?

[Ice]

Just wondering if anybody had any more ideas I could try? Thanks!

[yyzyyz]

Try connecting to the console on sipsorcery to view the call setup logs.
You should be able to figure out what's going on...

[paramvirs]

I used SIP sorcery on my nokia E63.
Only incomming calls work for me. Outgoing calls connect but i cant hear other person.
Also the call quality is not very good. I have a Vonage phone line at my home and call quality from Sipsorcery is not comparable to it.
Tried fring also and that too have poor call quality.
Any suggestion to improve call quality?

[FONGO_steve]

Also the call quality is not very good. I have a Vonage phone line at my home and call quality from Sipsorcery is not comparable to it.

Keep in mind Sipsorcery isn't a provider, and Vonage is! The quality I get through sipsorcery is identical to that of connecting directly to freephoneline, for me at least

[paramvirs]

i had got FPL working on my Nokia E63. Check this configuration guide
viewtopic.php?f=15&t=1046