MichaelVoIP wrote:Is there a way to block the CID completely?
Officially, no. Freephoneline changed its policy years ago. They stopped allowing *67 to work at the provider level (see #1 below) to prevent abuse. It's allowed for Fongo Home Phone users though:
https://support.fongo.com/hc/en-us/arti ... Home-Phone (go figure). There have been a few exceptions made for certain individuals using FPL, but it's rare
1) You can send *67 through the service provider, who then either accepts the star code or doesn't do anything. FPL, by default, doesn't do anything. At least that was the case the last time I tested.
2) You can have *67 processed by your ATA, which sends an anonymous call flag in the SIP header along the path to the receiving carrier that, in turn, has to recognize and agree to not show CID. *67 (outgoing CID block). Calls to Telus mobile numbers worked when *67 is processed by Obihai ATAs immediately after server migration. No CID info appeared on the receiving end. I'm not sure if *67 still works (I'm too busy to test this). But I know it did work for Obihai ATAs immediately after server migration because I tested by dialing Telus Mobility numbers.
In this case you're doing #2. When *67 is parsed by an ATA or IP Phone, my FPL number constantly appears when calling Fongo Mobile numbers. But it's blocked when calling regular Telus mobile numbers, for example. Telus Mobility acknowledges the CID block flag and complies. Fongo Mobile doesn't. For whatever reason *67 seems to work with Obihai ATAs and IP Phones, at least when calling non-VoIP numbers.
If my FPL account accepted the *67 code (when sending *67 through FPL and not having the star code processed by my ATA instead) and agreed to block outgoing CID, my FPL number would not appear when calling Fongo Mobile numbers. Refer to point #1.
A. FPL doesn't support *67 (anonymous call blocking), officially, at the provider level. Whether it works is dependent upon the ATA.
B. Using *67 in Linksys ATAs/Cisco ATAs with FPL has been reported to drop calls after 15 minutes.
So, using it should be avoided.
In your ATA, navigate to Voice tab-->Line tab (whichever you use for FPL)-->Supplementary Service Subscription-->Block CID Serv:
a) change to no
b) Click "submit"
Do this to avoid 15 minute call disconnections with Freephoneline.
albeause wrote:Hi !
To answer your question,, yes it drops in 15 mins every single time, when the *67 is activated. I tried FPL to Bell lan line, FPL to cellphone Videotron and FPL to Bell Mobility. All three does the same result after 15mins mark,, the call dropped.
I did capture syslogs, with spa2102 set in full debug, and it does not show the issue. The SIP/2.0 200 Ok and NOTIFY sip messages are still transmitting from the ATA to the proxy even the call is dropped on the cellphone (which it could be normal to continue the registration). There is no special log when the call drop. I remark is when the disconnect occurs on the cellphone on the 15 mins, there is no hang up logs (BYE Sip, CC: ended, FM Alert Stop Rx Tx, or AUD rel Call). Normally without *67, (*68 activated) when the other end hangs up,, you get these logs and also you will get the busy tone, followed with a fast busy tone. You don't hear any tone when *67 is activated, it comes dead-air.
Cyber wrote:
2020-01-20 - 10:48 (EST) ISSUE SOLVED
After more than 4 hours of calls test, I found what cause the outgoing call drop.
Before the migration, blocked CID calls was showing "ANONYMOUS".
After the migration, blocked CID calls show "unavailable".
The issue is with the Caller ID. I turned off Block CID Serv and no more call drop at 15 minutes 04 seconds
Cyber wrote:The bug seem to be the "Block CID Serv" feature with the SPA112.
TEST #1 :
Block CID Serv set to "NO"
Display Name set to "Anonymous"
I called my Koodo mobile phone. Caller ID and call log on my mobile phone show "Private Call".
No disconnect after 15 minutes.
TEST #2 :
Block CID Serv set to "YES"
Display Name set to "Anonymous"
I called my Koodo mobile phone. Caller ID on my mobile phone show "Private Call" and call log show "unavailable".
The call drop after 15 minutes.
---------------------------------------
The issue is related with the "Block CID Serv" feature and "unavailable" Caller ID in my mobile phone call log.
I had a similar conversation over here with a Grandstream user:
viewtopic.php?f=8&t=20194&p=78948.
and
viewtopic.php?f=8&t=19391&p=75892