can't hear other side voice when make call or receive call
-
- Just Passing Thru
- Posts: 6
- Joined: 02/19/2015
- SIP Device Name: OBI100
- Computer OS: Win7
- Router: TP-Link AC2 AC750 Gigabit
Re: can't hear other side voice when make call or receive ca
Argh I'm back to square one.
Inbound calls go straight to v-mail. Call log shows 2 entries for each call. First normal call clearing. Second disconnect reason = user busy.
Outbound starts with 11 quick beeps followed by dial tone. I can enter the 10 digits but get the following messages. That password is not valid, then, ..rejected by the service provider reason is 603. At least I'm getting feedback?
I reset OBI then updated to Rogers cable configuration.
OBITalk site shows registered. Test call works.
FPL site SIP Status = connected.
Thoughts?
Inbound calls go straight to v-mail. Call log shows 2 entries for each call. First normal call clearing. Second disconnect reason = user busy.
Outbound starts with 11 quick beeps followed by dial tone. I can enter the 10 digits but get the following messages. That password is not valid, then, ..rejected by the service provider reason is 603. At least I'm getting feedback?
I reset OBI then updated to Rogers cable configuration.
OBITalk site shows registered. Test call works.
FPL site SIP Status = connected.
Thoughts?
-
- Tried and True
- Posts: 411
- Joined: 08/14/2014
- SIP Device Name: OBi110
- Firmware Version: 1.3.0 (Build: 2824)
- ISP Name: Telus
- Computer OS: Windows 7
- Router: Toastman Tomato
Re: can't hear other side voice when make call or receive ca
I just found something interesting.
I set up a softphone with an FPL number, but the wrong password. It successfully registered, but I could not make or receive calls. I heard the same message you did.
Double check your password, noting that the password you use to log in to the FPL website is different.
When my softphone responded incorrectly to the challenge, FPL responded with 200 Auth failed. My softphone interpreted 200 as a successful registration. VoIP.ms responds with 403 Forbidden for auth failure, or 200 OK for success. I've never heard of 200 Auth failed before.
As for your inbound call problem, now that the symptoms have changed I'm going to disagree with my own post from before. I think you have DND enabled. Check Voice Services >> SP1 Service >> DoNotDIsturbEnable and see if I'm right.
I set up a softphone with an FPL number, but the wrong password. It successfully registered, but I could not make or receive calls. I heard the same message you did.
Double check your password, noting that the password you use to log in to the FPL website is different.
When my softphone responded incorrectly to the challenge, FPL responded with 200 Auth failed. My softphone interpreted 200 as a successful registration. VoIP.ms responds with 403 Forbidden for auth failure, or 200 OK for success. I've never heard of 200 Auth failed before.
As for your inbound call problem, now that the symptoms have changed I'm going to disagree with my own post from before. I think you have DND enabled. Check Voice Services >> SP1 Service >> DoNotDIsturbEnable and see if I'm right.
-
- Just Passing Thru
- Posts: 6
- Joined: 02/19/2015
- SIP Device Name: OBI100
- Computer OS: Win7
- Router: TP-Link AC2 AC750 Gigabit
Re: can't hear other side voice when make call or receive ca
Thanks Mango, I did end up at the password since it's hidden and I couldn't verify. Updated it according to FPL page and it now outgoing calls work!
But the DoNotDisturbEnable is NOT checked off. Incoming still going to vmail.
Wait...Now the unit is ringing with an incoming call!! And it seems to be working!
Ok it seems all is working both ways now. Strange. Delays in systems activating?
Thanks again for your help.
But the DoNotDisturbEnable is NOT checked off. Incoming still going to vmail.
Wait...Now the unit is ringing with an incoming call!! And it seems to be working!
Ok it seems all is working both ways now. Strange. Delays in systems activating?
Thanks again for your help.
-
- Just Passing Thru
- Posts: 11
- Joined: 09/03/2014
- SIP Device Name: Grandstream HT701
- Firmware Version: 1.0.6.1
- ISP Name: Rogers Cable
- Computer OS: Windows 8
- Router: CGN3ROG
One way audio
Just replaced my modem/router. I currently have a Grandstream HT701 that was using a Hitron CGN3 from Rogers. I switched my Hitron with a Cisco DPC3825 last night(still Rogers). I am connected with a dial tone but when I make a call, I don't hear the ringing or the person on the other line.
I have port forwarding setup correctly (I think) and I placed the HT701 in DMZ on the router. Not sure what else needs to be done.
Anyone have a working config with these two devices that they can share with me?
Much Appreciated.
Mike
I have port forwarding setup correctly (I think) and I placed the HT701 in DMZ on the router. Not sure what else needs to be done.
Anyone have a working config with these two devices that they can share with me?
Much Appreciated.
Mike
-
- Just Passing Thru
- Posts: 3
- Joined: 12/18/2014
- SIP Device Name: SPA112
- Firmware Version: 1.3.3(015)
- ISP Name: Rogers
- Computer OS: XP
- Router: Linksys WRT54Gv8 w DD-WRT
Re: can't hear other side voice when make call or receive ca
Update to my earlier post on this subject.
There was a question about whether I was using the router as a bridge - the answer is no. I had a dumb modem from Rogers and needed a conventional router.
More interesting is my experience today when I switched my Internet access from Rogers to Primus. I again could not hear the other side of the call. This became apparent when testing my alarm system - it could not connect to the alarm station because it could not hear the incoming tone from the computer on the other end. This time I only had to change the proxy setting from voip4.freephoneline.ca:6060 to voip3.freephoneline.ca to solve the problem.
There was a question about whether I was using the router as a bridge - the answer is no. I had a dumb modem from Rogers and needed a conventional router.
More interesting is my experience today when I switched my Internet access from Rogers to Primus. I again could not hear the other side of the call. This became apparent when testing my alarm system - it could not connect to the alarm station because it could not hear the incoming tone from the computer on the other end. This time I only had to change the proxy setting from voip4.freephoneline.ca:6060 to voip3.freephoneline.ca to solve the problem.
-
- Tried and True
- Posts: 411
- Joined: 08/14/2014
- SIP Device Name: OBi110
- Firmware Version: 1.3.0 (Build: 2824)
- ISP Name: Telus
- Computer OS: Windows 7
- Router: Toastman Tomato
Re: can't hear other side voice when make call or receive ca
There were no reports of this for a while and I was hopeful that the admins had fixed voip, voip2, and voip4.
- Fongo Support
- Site Moderator
- Posts: 1689
- Joined: 01/01/2013
Re: can't hear other side voice when make call or receive ca
Hi,Mango wrote:Rats. There were no reports of this for a while and I was hopeful that the admins had fixed voip, voip2, and voip4.
Sorry for my ignorance- who are the "rats"?
regards,
-
- Tried and True
- Posts: 411
- Joined: 08/14/2014
- SIP Device Name: OBi110
- Firmware Version: 1.3.0 (Build: 2824)
- ISP Name: Telus
- Computer OS: Windows 7
- Router: Toastman Tomato
Re: can't hear other side voice when make call or receive ca
I apologize for the confusion. I wasn't referring to anyone. It was a statement to express mild disappointment like "bother" or "darn it".
- Fongo Support
- Site Moderator
- Posts: 1689
- Joined: 01/01/2013
Re: can't hear other side voice when make call or receive ca
Hi there,Mango wrote:I apologize for the confusion. I wasn't referring to anyone. It was a statement to express mild disappointment like "bother" or "darn it".
Thanks for the clarification. I am sure that Jake and any mod can explain to you what work has been done so far from 2012 to present so you can have a better understanding of the back end before you make statements like the one above.
Regards
-
- Tried and True
- Posts: 411
- Joined: 08/14/2014
- SIP Device Name: OBi110
- Firmware Version: 1.3.0 (Build: 2824)
- ISP Name: Telus
- Computer OS: Windows 7
- Router: Toastman Tomato
Re: can't hear other side voice when make call or receive ca
If I offended you, I regret that. It was not intentional.
- ckkatan
- Active Poster
- Posts: 74
- Joined: 11/29/2014
- SIP Device Name: Cisco
- ISP Name: DSL
- Router: Linksys
Re: can't hear other side voice when make call or receive ca
I would like to know what works have been done so far. Can this information be shared in the Forum? If not, please PM me as well. Thanks.Fongo Support wrote:Hi there,Mango wrote:I apologize for the confusion. I wasn't referring to anyone. It was a statement to express mild disappointment like "bother" or "darn it".
Thanks for the clarification. I am sure that Jake and any mod can explain to you what work has been done so far from 2012 to present so you can have a better understanding of the back end before you make statements like the one above.
Regards
- Fongo Support
- Site Moderator
- Posts: 1689
- Joined: 01/01/2013
Re: can't hear other side voice when make call or receive ca
Hi there,ckkatan wrote:I would like to know what works have been done so far. Can this information be shared in the Forum? If not, please PM me as well. Thanks.Fongo Support wrote:Hi there,Mango wrote:I apologize for the confusion. I wasn't referring to anyone. It was a statement to express mild disappointment like "bother" or "darn it".
Thanks for the clarification. I am sure that Jake and any mod can explain to you what work has been done so far from 2012 to present so you can have a better understanding of the back end before you make statements like the one above.
Regards
I just send you a PM.
Please let me know if the service is working for you as per your expectations.
regards,
-
- Just Passing Thru
- Posts: 11
- Joined: 09/03/2014
- SIP Device Name: Grandstream HT701
- Firmware Version: 1.0.6.1
- ISP Name: Rogers Cable
- Computer OS: Windows 8
- Router: CGN3ROG
Re: One way audio
smichael777ca wrote:Just replaced my modem/router. I currently have a Grandstream HT701 that was using a Hitron CGN3 from Rogers. I switched my Hitron with a Cisco DPC3825 last night(still Rogers). I am connected with a dial tone but when I make a call, I don't hear the ringing or the person on the other line.
I have port forwarding setup correctly (I think) and I placed the HT701 in DMZ on the router. Not sure what else needs to be done.
Anyone have a working config with these two devices that they can share with me?
Much Appreciated.
Mike
Anybody?
![Sad :(](./images/smilies/icon_e_sad.gif)
-
- Tried and True
- Posts: 411
- Joined: 08/14/2014
- SIP Device Name: OBi110
- Firmware Version: 1.3.0 (Build: 2824)
- ISP Name: Telus
- Computer OS: Windows 7
- Router: Toastman Tomato
Re: can't hear other side voice when make call or receive ca
Please try the following:
1) Disable DMZ and your port forwarding.
2) Follow the instructions in my post in this thread: http://forum.fongo.com/viewtopic.php?f=15&t=16292
3) Be sure your device is configured as per the PDF in the above thread, being sure to use voip4.freephoneline.ca:6060 as the Primary SIP Server.
Let us know if that works.
1) Disable DMZ and your port forwarding.
2) Follow the instructions in my post in this thread: http://forum.fongo.com/viewtopic.php?f=15&t=16292
3) Be sure your device is configured as per the PDF in the above thread, being sure to use voip4.freephoneline.ca:6060 as the Primary SIP Server.
Let us know if that works.
-
- Just Passing Thru
- Posts: 11
- Joined: 09/03/2014
- SIP Device Name: Grandstream HT701
- Firmware Version: 1.0.6.1
- ISP Name: Rogers Cable
- Computer OS: Windows 8
- Router: CGN3ROG
Re: can't hear other side voice when make call or receive ca
Thanks for the help Mango. But when I made these changes, the phone tells me: "device not registered" ![Sad :(](./images/smilies/icon_e_sad.gif)
![Sad :(](./images/smilies/icon_e_sad.gif)
-
- Tried and True
- Posts: 411
- Joined: 08/14/2014
- SIP Device Name: OBi110
- Firmware Version: 1.3.0 (Build: 2824)
- ISP Name: Telus
- Computer OS: Windows 7
- Router: Toastman Tomato
Re: can't hear other side voice when make call or receive ca
That's a new one.
Put your DMZ back in place, just for testing purposes and see if that solves the problem.
If that does not solve the problem, the other possibility is the server banned you for registering too frequently. In that case, you will need to disable DMZ and unplug your device for an hour.
Put your DMZ back in place, just for testing purposes and see if that solves the problem.
If that does not solve the problem, the other possibility is the server banned you for registering too frequently. In that case, you will need to disable DMZ and unplug your device for an hour.
-
- Just Passing Thru
- Posts: 11
- Joined: 09/03/2014
- SIP Device Name: Grandstream HT701
- Firmware Version: 1.0.6.1
- ISP Name: Rogers Cable
- Computer OS: Windows 8
- Router: CGN3ROG
Re: can't hear other side voice when make call or receive ca
Put the device back into DMZ and the phone works but i'm still back to square one with the one-way audio.
- Fongo Support
- Site Moderator
- Posts: 1689
- Joined: 01/01/2013
Re: can't hear other side voice when make call or receive ca
Hi,smichael777ca wrote:Put the device back into DMZ and the phone works but i'm still back to square one with the one-way audio.
Please open a support ticket :
http://support.fongo.com/anonymous_requests/new
Send me a PM with the ticket# once you receive it.
Regards,
-
- Just Passing Thru
- Posts: 11
- Joined: 09/03/2014
- SIP Device Name: Grandstream HT701
- Firmware Version: 1.0.6.1
- ISP Name: Rogers Cable
- Computer OS: Windows 8
- Router: CGN3ROG
Re: can't hear other side voice when make call or receive ca
Done. Thanks so much for your help!
-
- Just Passing Thru
- Posts: 11
- Joined: 09/03/2014
- SIP Device Name: Grandstream HT701
- Firmware Version: 1.0.6.1
- ISP Name: Rogers Cable
- Computer OS: Windows 8
- Router: CGN3ROG
Re: can't hear other side voice when make call or receive ca
All good now. Thanks for the help Mango and Fongo! My account was indeed locked for some reason
-
- Tried and True
- Posts: 411
- Joined: 08/14/2014
- SIP Device Name: OBi110
- Firmware Version: 1.3.0 (Build: 2824)
- ISP Name: Telus
- Computer OS: Windows 7
- Router: Toastman Tomato
Re: can't hear other side voice when make call or receive ca
To make sure I understand it correctly,
1) You submitted a ticket.
2) Fongo Support did something.
3) You did not change your configuration, but your service started working.
Is that right?
1) You submitted a ticket.
2) Fongo Support did something.
3) You did not change your configuration, but your service started working.
Is that right?
-
- Just Passing Thru
- Posts: 11
- Joined: 09/03/2014
- SIP Device Name: Grandstream HT701
- Firmware Version: 1.0.6.1
- ISP Name: Rogers Cable
- Computer OS: Windows 8
- Router: CGN3ROG
Re: can't hear other side voice when make call or receive ca
Just had to change my SIP password as they changed it
-
- One Hit Wonder
- Posts: 1
- Joined: 03/18/2015
- SIP Device Name: ATA122
- Firmware Version: 1.3.5
- ISP Name: WTC
- Computer OS: Win Vista
- Router: Dlink615
Choppy voice cant understand other person
Hi there, I've read all the forums re: choppy voice and researched best codecs for voice etc. MY problem might be a bit different tho, and I hope someone has ideas? Before we did a port-forward with our bell home number, we enjoyed a fongo (FPL?) phone number and the it was great! the voice quality was great, and all calls were made successfully. We followed the generic setup for our ATA122 and DLINK615 (including basic QoS allowed).... With a minimum setup, the fongo number was awesome. We were ready to let go of our home line. Ever since we did the porting, its been a disaster. Most calls are 'garbled', and often we can't make out what the other person is saying. This is our biggest issue at the moment, but we have others too --> for example, sometimes we'll dial a number and get a totally different responder (ie, we'll make a local call and we end up rining a random person in another city!) -- and we've also rang a local number many times and it shows as number busy, but when we dial from our cell, it rings right thru... So, we're pretty disappointed with the porting and wish we could have the fongo (FPL) phone number back...
Does anyone have suggestions?
After the porting and can't hear the other people, we've setup G711u as our first preferred codec, and g729a as our second preferred. finally, both the ATA122 and dlink615 have the latest firmware... but like said, everything was super awesome with the fongo number... what happened during the porting???
please and thanks!
![Sad :(](./images/smilies/icon_e_sad.gif)
After the porting and can't hear the other people, we've setup G711u as our first preferred codec, and g729a as our second preferred. finally, both the ATA122 and dlink615 have the latest firmware... but like said, everything was super awesome with the fongo number... what happened during the porting???
please and thanks!
-
- Just Passing Thru
- Posts: 7
- Joined: 03/18/2015
- SIP Device Name: HT702
- ISP Name: Rogers
- Router: AC 1700 Nighthawk
Re: can't hear other side voice when make call or receive ca
my FPL can't hear other side voice, other side can hear my voice. it happen on both outgoing and incoming call, i use it for long time and no issue
my ISP is Acanac
when make outgoing call, I can't hear ring back tone,[/quote]
I have an the same issue new setup and Have set it up per guide. I have also set it up direct to remove the router as an issue. Sip status shows as connected on the management page.
Gone through the the forums at length
submitted a ticket but got the 'blow off' not supported response.
it seems the community here presents a good track record of support so I am reaching out for help Kind regards to all.
Splinter
my ISP is Acanac
when make outgoing call, I can't hear ring back tone,[/quote]
I have an the same issue new setup and Have set it up per guide. I have also set it up direct to remove the router as an issue. Sip status shows as connected on the management page.
Gone through the the forums at length
submitted a ticket but got the 'blow off' not supported response.
it seems the community here presents a good track record of support so I am reaching out for help Kind regards to all.
Splinter
-
- Just Passing Thru
- Posts: 7
- Joined: 03/18/2015
- SIP Device Name: HT702
- ISP Name: Rogers
- Router: AC 1700 Nighthawk
Re: can't hear other side voice when make call or receive ca
All working good now! Created a ticket and FPL forced registration. it seems the "blow off" response is automated. it was followed up with and now - Joy.... Porting request submitted <grin>