almost every call is dropping after 32 secs

[FONGO_kris]

Can you screenshot the "System" tab so I can see what this "Invalid Domain" really is?

[Scoponox]

Like I mentioned above I tried a static IP but the router for some reason doesn't see if when the ATA has a static IP ...so I turned off DHCP on now

[tony_qc]

Its a firmware issue ...... I have put your firmware and now I have the same problem
But I have many tricks in my bag

[tony_qc]

k I have made a fix
here we go

- Click the Start button, then select Run.
- Type: telnet 192.168.254.254 (IP of Your Speedsream but im using 192.168.2.1 because I can use my old file for the hide QOS ) then select OK
- Type username: admin and password admin
- Type: cfg upro{ac2{qos=y
- Type: cfg save
- Type: cfg napt{dsip=y
- Type: cfg save
- Type: do reboot


BOOM FIXED

[tony_qc]

can you make a phone call over 10 min to see if its work...

call *98 and spam 3*3*3*3*3*3*3*3.................

or make a regular call

[Scoponox]

IT WORKS! Thank you very much tony_qc I think that did it! Coincidentally Bell finally came today to install my dryloop... but I made a call over 10 mins! Hopefully it keeps working. How did you find out about these settings to the QOS?

I think it is related to the firmware though because the firmware was set up for BigPond for Australian/New Zealand. I found this link explaining it and made the necessary changes...it allows both routed & bridged PPPoE:
http://www.dslreports.com/forum/r196380 ... d-firmware

1. Log in as admin user
2. Click on the Gateway icon on top
3. Click on ISP Connection icon on the left
4. Click Advanced settings
5. Click "Configure ATM Virtual Circuit"
6. Delete any entries inside
7. Click Add a new VC

1. ATM Settings:
VPI: 0, VCI: 35
Encapsulation type LLC
Traffic Class: Unspecified Bit Rate
Rest: Blank
Click Next

2. Protocol Selection:
PPPoE
Click Next

3. PPPoE Type
With PPPoE Bridge
Click Next

4. PPPoe With Bridge
NO
Click Next

5. PPPoE Session Count
One
Click Next

6. User Information
Enter your ISP login/pass
Click Next

7. PPPoE Options
your choice of options, self explanatory
Leave MTU at 1492
Click Next

8. PPP Static IP
Leave Blank
Click Next

9. Interface Options
Enable Firewall/Attack Detection Syystem if desired
RIP Disabled
NAT/NAPT: NAPT
Click Next

10. Connection Name
Enter a name, ie: 0/35 DSL etc.
Click Next

11. ATM Virtual Circuit Wizard
Click Finish to save the settings

Finished Virtual Circuit settings should look like this

#0 0/35 2684 Virtual Circuit
OE BRG
PPPoE 0/35 DSL (if you named the connection that)

Reboot the modem manually or in the interface.

I also finally got the ATA properly configured with a static IP and the routers sees it too.

[tony_qc]

I used those settings to have internet back..

[Scoponox]

but how did you figure it out. Good job. This was becoming very frustrating.

[tony_qc]

do you have the wireless light green?

[Scoponox]

Yes I do. At first it didn't come on but once I connected with my wireless laptop it start working.

What i did notice though is that if the phone is in use the internet slows down to almost a stop. But this was happening before I switched to FPL too.

[Scoponox]

Yes it is with the wireless. So how do I go about changing the QOS?

[tony_qc]

you can access the QOS settings with the file I posted here http://forum.freephoneline.ca/viewtopic.php?f=14&t=298 I tryed to enable the qos setting with this cfg upro{ac2{qos=y but don't work......... then now im stopping to work on this modem since all work with the bell firmware .... But I can't go back to the bell firmware... anyway I have 2 bell modems....

sorry for my english

[tony_qc]

if you want to use my file you need to change your modem ip to 192.168.2.1

[tony_qc]

oh forgot to say you can't enable Qos with your firmware same if you have access to with the file.....

[Scoponox]

So are you saying that the QOS isn't going to work with this config file?

[tony_qc]

yep and with any files