Caller id display (phone number) is not working

[levgersh]

When I receive a call, I no longer see a phone number of the person calling me.
Please help

[Liptonbrisk]

When I receive a call, I no longer see a phone number of the person calling me.
Please help

These are the steps I would try, step by step, down the list:

1. Disable Follow Me while troubleshooting. Login at https://www.freephoneline.ca/followMeSettings. Change "Status" to "Disable". Click Submit.

For what it's worth, you won't see Caller ID appear on the phone attached to the ATA when using "Sequential" with "Always Call Forward" (Follow Me mode). When Sequential Follow Me is used in conjunction with "Always Call Forward", the first number in the list will ring first and your Freephoneline number will be skipped. When the call is answered by the first number in the list (or by its respective voicemail system), the ATA's phone will never ring.

b) Ensure that “Rings before voicemail” is greater than one: login at https://www.freephoneline.ca/voicemailSettings.

2. Login at https://www.freephoneline.ca/showSipSettings.
SIP Status needs to indicate "Connected", and SIP User Agent should reflect the ATA you're using.

If your ATA isn't registered, your phone(s) used for FreePhoneLine (FPL) can't ring. If it doesn't ring, no Caller ID (CID) info can appear.



3. Login at https://www.freephoneline.ca/callLogs to confirm whether incoming calls are reaching your FPL account (they should be if incoming calls are reaching your FPL voicemail message). Select "current and previous month". Click the "SUBMIT" button. Only calls that are answered in some manner (including being answered by FPL's voicemail system) will appear in FPL's call list. Calls that aren't answered (cancelled before being answered) aren't listed. Duration is rounded to the next minute.

Does the incoming caller number appear there? It should provided you answered the call or provided Freephoneline's voicemail system did.


4. a) Dial ****
b) Then dial 110#
c) Enter the IP address you hear into a web browser.
d) Login to your ATA.
e) Always choose the admin login and advanced view menus (select "advanced")

5. Navigate to Voice-->Info tab-->Line (used for FPL) Status (this is not a tab)-->Registration State
Ensure your Line is registered.

If steps 2 and/or 4 indicate the ATA isn't registered, click viewtopic.php?f=8&t=20532, and follow the steps from that link until your ATA is registered.


6. Navigate to Info-->Scroll down until you see "Line [the line used for FPL] Status"
Note that "Line Status" is not a tab
You want to look for "Line 1 Status", for example (if Line 1 is used for FPL).


7. Check "Last Caller Number" for the Line 1 (or 2, if Line 2 is use for FPL) Status. What is the Last Caller Number? Is it the last number that called you?

"Last Caller Number" is on the right hand side.

So, to check to see whether the most recent incoming call is reaching your ATA, login to it via its web user interface (step 4 above). Select "admin", select "advanced view", and navigate to Info tab-->Line (used for FPL) Status (this is not the Line tab; you should be on the Info tab still)-->Last Caller Number. You'll see the most recent incoming call number that reached your ATA. Unfortunately, you can only see the most recent incoming caller number (not past ones).

If the most recent (incoming) caller number is listed in the ATA (Last Caller Number), then the problem isn't on FPL's end.

You can test by calling your FPL number again and letting the phone ring several times before checking "Last Caller Number".


8. Navigate to Voice--Regional tab-->(scroll down to) Miscellaneous-->

a) Caller ID Method should be Bellcore (N.Amer,China)
b) Caller ID fsk standard should be bell 202

Transmission of Caller ID occurs between the first and second ring.


9. Navigate to the Line tab (1 or 2) that is used for Freephoneline.

a) Scroll down to "Supplementary Service Subscription"
b) What is "CID Serv" set to? It should be set to "yes".
c) CWCID Serv should also be set to yes.


10. If a cordless phone is being used, it's the job of the phone base to transmit CID (caller ID) information to the handset being used. If a cordless handset is being used, I would try rebooting (or power cycling off/on) the base and ensuring the handset is close to the base when an incoming call occurs. Possibly deregistering or unpairing a handset from the base and registering it again may help.
If it's a Panasonic cordless phone, you may find some hints here: https://cordlessguy.com/caller-id-not-w ... ess-phones (the first, bolded paragraph may help, and the rest I would be inclined to ignore).

11. Ensure the ATA is not connected to any wall jack in the dwelling. Wiring ATAs into existing phone jacks can fry ATAs if the phone company's line hasn't been disconnected at the demarc. If the ATA is damaged, it's reasonable to expect problems.

Also check to ensure that you don't have too many phones wired to the ATA. Google/search "Ringer equivalence number" (REN). If you have a lot of wired phones, just test with a single phone for now.

12. Check to ensure all phone cords are properly seated.

13. Test with an incoming call again. If you're using a cordless phone, only check the handset that is connected to the phone base, which should be, in turn, wired directly to the ATA. Don't bother looking at the other handset extensions.

14. Same problem? Check for a damaged ATA phone port on back of unit.

To test,

a) disable the current line used for FPL. Navigate to Line tab used for FPL-->
For "Line enable" select "no." And save settings.

b) Now provision the other ATA line for FPL using this guide: viewtopic.php?f=15&t=16294. If you experience a registration issue, check your settings against what's listed at viewtopic.php?f=8&t=20532.

Afterwards try the other phone port instead on the back of the ATA instead (you should be using a different ATA line now). Obviously, if that works, one of the ATA's phone ports is damaged, and it would be time for a new ATA.

Keep this in mind: when there are multiple devices/softphones/Lines (on an ATA or IP Phone) using the same FPL account, only the most recent registration is valid. The previously registered device (or ATA line) will lose registration when using the same proxy server, and, consequently, incoming calls will not ring on the previously registered device or ATA Line, in this case. This is especially important to consider if someone else is using your SIP credentials (username and password) that are found after logging in at https://www.freephoneline.ca/showSipSettings or if you're trying to register your FPL account with a smartphone SIP app (or FPL desktop app), with another device, or more than one ATA or IP Phone line, in this case. Registration is required for incoming calls. It is not required for outgoing calls (except if you want calls to continue past 15 minutes). Only one registration per FPL account is allowed at any time. A single line on an ATA or IP Phone is one registration. A SIP app is another.

That is, don't enable both Lines of your ATA (related to step 12a; "Line enable" should not be set to "yes" for both ATA lines, unless you own two VoIP unlock keys), when using the same FPL proxy server with the exact same FPL account on both ATA lines.


15. If you can, try another power cord/supply for the ATA.

[Liptonbrisk]

(continued)

16. Click http://genuinelinksys.blogspot.com/2011 ... nuine.html
Are you use a fake PAP2?
Real ones have not been sold since 2012, when they were discontinued: https://www.cisco.com/c/en/us/obsolete/ ... ports.html.

You can also check at https://voipfan.net/other/fakepap2.php

Fakes are potential fire hazards: https://goughlui.com/2016/05/01/failed- ... ms-050200/

Fakes aren't, in my opinion, worth troubleshooting.