Linksys PAP2 phone doesn't ring

[ffkly]

setup is fine, I can call and receive calls, phone just doen
t ring, any solutions? thanks

[FONGO_kris]

What kind of phone are you using? Some phones have a specific set, or range of frequencies that they like to use.

Our recommended settings are for any old analog phone. Check the box your phone came in for set frequencies or even better, the internet!

[Jake]

setup is fine, I can call and receive calls, phone just doen
t ring, any solutions? thanks

Have you tried plugging in another phone? It could be something simple like the ringer just doesn't work on that phone.

[ffkly]

Thanks for the reply.
I bought this one on ebay, it is refurbished, it didn't come with mannual, I tried different voltage and frequency settings, didn't work.

http://electronics.become.com/uniden-de ... c212282583

[FONGO_steve]

Thanks for the reply.
I bought this one on ebay, it is refurbished, it didn't come with mannual, I tried different voltage and frequency settings, didn't work.

http://electronics.become.com/uniden-de ... c212282583

Have another line to try the phone on to make sure it isn't a dead phone? I used to sell refurb phones when I worked in a liquidation store, uniden's were always hit and miss for the refurb quality.

And our default ring values are just fine. It's a digital phone, so it'll run just perfectly with the values we provide.

[ffkly]

I don't have any other phone or other lines, I cannot test, when I call my FPL number, phone doesn't ring, doesn't flash, but if I press answer, it is connected and worked fine

[ffkly]

I searched online, people say ATA only works with analog phones, is that true?

[FONGO_kris]

Not at all, I have an General Electric ATLINKS USA Digital phone here on our PAP2T...

Try lower frequencies like 27 / 42

[FONGO_steve]

I don't have any other phone or other lines, I cannot test, when I call my FPL number, phone doesn't ring, doesn't flash, but if I press answer, it is connected and worked fine

Could possibly be the phone.. Digital phones aren't specific to voltage requirements, as long as they detect a voltage, they will ring. I'm using a Pansonic DECT6.0 phone on my ATA at home and haven't changed it from the device's default ringer settings.

[ffkly]

what is your voltage and frequency setting? Thanks

[FONGO_kris]

Ring Type: Sinusoid @ 52v / 90Ghz --- Voltage / Frequency

[ffkly]

tried lot of settings, still not working. is this related to port forwarding issue? I tried to open the ports in my router, after that the phone stopped working completely, cann't even hear dial tone. also tried to turn off DHCP and assign an IP to ATA, I got "cannot log into server" error.

[mohnashaat]

are you sure ur telephone isn't on mute ringer? u have to test it anywhere easier than trying a lot of complicated issues

[ffkly]

it's not muted, there is a function, two headsets can call each other, I tried, they both can ring

[canadianlog]

I have same issue, I can make call from and to the phone. But no ringer at the phone. I tried from my phone to my voip phone i can hear it ringing on my regular phone but actually voip phone does not ring. But if pick it up i can talk normal also I can make calls as well.
I have tried 3 different phones and i know ringer works on them as i tested them on my regular land phone line.
I am using Linksys PAP2 adapter Firmware 3.1.22(LS).
Any help would be appreciated.

[oba]

Follow the instructions provided here :
http://forum.freephoneline.ca/viewtopic.php?f=14&t=298

The only change you have to make is to use LINE 2 and USER 2 and of course the plug line 2 on your ATA modem. This works for me.I have a digital UNIDEN phone.Good luck !